首页
1
商品介绍
2
Model 12C3
https://www.bestt.com.tw/yellowpage/ 贝斯科技股份有限公司

421

Model 12C

Picoprobe Arm and tip


The PICOPROBE® MODEL 12C is a high speed, high input impedance active probe for measuring the internal node voltage of integrated circuits. The input is 1 megohm shunted by 0.1 pf and the rise/fall times are 0.8 ns. This instrument has full dc capability and can be used with any oscilloscope. The Model 12C was specially designed so that when used in conjunction with a high input impedance oscilloscope, signal attenuation is 10:1 and with a 50 Ohm input, signal attenuation is 20:1.

Rugged, dependable and high speed the Model 12C presents a very modest load to the integrated circuit. It can be used to troubleshoot high speed bipolar, NMOS and CMOS circuits-even some short holding time dynamic nodes. Each amplifier is individually optimized for peak performance and reliability. The Model 12C will withstand large input over voltages. The only known failure mode is the accidental breaking or crushing of the probe tip which can be easily replaced. A large selection of replaceable probe tips are available to accommodate a variety of probing needs.

Specifications
 Input Capacitance  0.1pf
 Input Resistance  1.0 megohm
 Rise/Fall Time  0.8ns
 Bandwidth  dc to 500 MHz
 Linearity  0.5%
 Voltage Range  -10 to +20V*
 Gain Accuracy  ±3%
 Signal Attenuation  (High Input impedance oscilloscope: 10 to1) (50 ohm input: 20 to 1)
FIGURE 2

Picoprobe® Model 12C Replacement Tips

Part Number

Tungsten Wire
Shaft Diameter

Point Radius
 
12C-1-5

5 micron

12c-1.jpg
12C-1-10

10 micron

<0.1 micron="" center="">0.10.1
12C-1-22

22 micron

<1.0 micron="" center="">1.01.0
12C-1-35

35 micron

<2.0 micron="" center="">2.02.0
12C-1-60

60 micron

<3.0 micron="" center="">3.03.0
12C-1-125

125 micron

<5.0 micron="" center="">5.05.0
 
12C-2-5

5 micron

12c-2.jpg
12C-2-10

10 micron

<0.1 micron="" center="">0.10.1
12C-2-22

22 micron

<1.0 micron="" center="">1.01.0
12C-2-35

35 micron

<2.0 micron="" center="">2.02.0
12C-2-60

60 micron

<3.0 micron="" center="">3.03.0
12C-2-125

125 micron

<5.0 micron="" center="">5.05.0

12C-4-5

5 micron

12c-4.jpg
12C-4-10

10 micron

<0.1 micron="" center="">0.10.1
12C-4-22

22 micron

<1.0 micron="" center="">1.01.0
12C-4-35

35 micron

<2.0 micron="" center="">2.02.0
12C-4-60

60 micron

<3.0 micron="" center="">3.03.0
12C-4-125

125 micron

<5.0 micron="" center="">5.05.0
FIGURE 3  


The Model 12C replacement tip slides easily in and out of the Model 12C Picoprobe® body. The replacement tip consists of a housing, a precision resistor/capacitor combination, and a tungsten probing wire that is tapered to a fine point. The tungsten wire allows ample flexing so the probe point and the circuit remain in contact even in the presence of probe table vibrations. The flexible wire even reduces the potential for damage to the circuit and probe point. Replacement tips are available with 10, 22, 35, 60, and 125 micron diameter wires which are sharpened as indicated in the table above.

*Special order Model 12C PICOPROBES® are available for -15V.

Requires the use of a Picoprobe® Power Supply. Please specify 110V or 220V when ordering.

pdf.jpgModel 12C Pdf
1239433